(r14) Barrick Lab :: ProtocolsElectrocompetentCells

---+ Electrocompetent _E. coli_

---++ Making Electrocompetent _E. coli_ Cells (small batch)

This procedure makes enough electrocompetent cells for 2-3 transformations.

   1 Grow an overnight culture of each strain in LB medium.
   1 Prepare 10 ml of fresh LB medium in a 50 ml flask for each strain.
   1 Inoculate with 100 ul of the overnight, stationary-phase culture. 
      * In general, inoculate to OD<sub>600</sub> of ~0.05.
   1 Grow the cells for approximately 2-3 hours, until they reach mid-exponential phase. 
      * In general, this is an OD<sub>600</sub> of ~0.6.
   1 Transfer the cells to 15 ml Falcon conical tubes.
   1 Pellet the cells by centrifugation for 5 minutes at 6,000 RPM. Remove promptly and pour off supernatant.
   1 Wash by adding 10 ml of chilled 10% glycerol to each tube, then vortexing vigorously to resuspend the pellet. Centrifuge for 3.5 minutes. Remove promptly and pour off supernatant. Repeat for at least four wash cycles in 10% glycerol.
   1 Resuspend in approximately 100 Âµl of 10% glycerol to make a 100x concentration of the initial culture.
   1 Divide into 30-50 Âµl aliquots in 0.5 or 1.7 ml tubes. Freeze or proceed directly to electroporation. Protocol for [[ProtocolsElectroporation][Electroporation of your Electrocompetent Cells can be found here]].

---+++ Notes

   1 Keeping the cells cold during all processing steps is recommended. Ideally, chill the subculture in an ice water bath for &gt;10 min before centrifuging, use a refrigerated centrifuge or a centrifuge in a cold room, and aliquot the final cell slurry into pre-chilled tubes for storage at -80C. These precautions are not strictly necessary if using the cells for routine cloning.
   1 Scale up the culture volumes if more electrocompetent cells are needed. The volume of 10% glycerol used for each wash should be at least 20Ã&mdash; the volume of the cell pellet.

---++ Making Electrocompetent _E. coli_ Cells (large batch)

   1 Grow an overnight culture of each strain in LB medium.
   1 Prepare 100 ml of fresh LB medium in a 500 ml flask for each strain.
   1 Inoculate with 1 mL of the overnight, stationary-phase culture. 
      * In general, inoculate to OD<sub>600</sub> of ~0.05.
   1 Grow the cells for approximately 3-4 hours, until they reach mid-exponential phase. 
      * In general, this is an OD<sub>600</sub> of ~0.6.
   1 Transfer the cells to 2x 50 ml Falcon conical tubes.
   1 Pellet the cells by centrifugation for 5 minutes at 6,000 RPM. Remove promptly and pour off supernatant.
   1 Wash by adding 40 ml of chilled 10% glycerol to each tube, then vortexing vigorously to resuspend the pellet. Centrifuge for 3.5 minutes. Remove promptly and pour off supernatant. Repeat for at least four wash cycles in 10% glycerol.
   1 Resuspend each pellet in approximately 500 Âµl of 10% glycerol to make a 100x concentration of the initial culture.
   1 Divide into 30-50 Âµl aliquots in 0.5 or 1.7 ml tubes. Freeze promptly at -80Ë&scaron;C.

When you're ready for electroporation, look at protocol here: [[ProtocolsElectroporation][Electroporation of your Electrocompetent Cells]]

---+++ References

   1 Short Protocols in Molecular Biology, Chapter 1.
   1 Datsenko, K.A., and Wanner, B.L. 2000. One-step inactivation of chromosomal genes in Escherichia coli K-12 using PCR products. Proc. Natl. Acad. Sci. U. S. A. 97: 6640-6645.

Barrick Lab > ProtocolList > ProtocolsElectrocompetentCells

Contributors to this topic

JeffreyBarrick, KateElston, DanielDeatherage, SeanLeonard, AdamHilterbrand, AlvaroRodriguez, LindseyWolf, JuliePerreau, DaciaLeon

Topic revision: r14 - 2017-04-11 - 19:50:07 - Main.JuliePerreau

Lab.ProtocolsElectrocompetentCells moved from Lab.ProceduresMakingElectrocompetentCells on 2010-05-07 - 15:02 by Main.JeffreyBarrick -