Large-scale Protein Expression in E. Coli:

Notes:

  • This can be applied to either soluble proteins (for a downstream prep in native conditions) or insoluble proteins in inclusion bodies (downstream denaturing prep)
  • Various expression systems can be used (IPTG, Arabinose, etc.?), the basic process is the same
  • Good resources for additional information: *The QiaExpressionist ([LINK])

Supplies:

  • 1L of appropriate media (LB can be used, 2xYT is richer and gives better growth; no experience with minimal media)
  • Agar plates (LB or 2xYT) w/ appropriate antibiotics
    • can add 0.2% glucose to cut down on leakiness of IPTG-inducible expression systems
  • Expression construct in an appropriate strain
    • ALWAYS good practice to get full insert sequence before starting experiment
    • Make sure host strain contains appropriate components for chosen expression system (e.g. T7 polymerase for T7-driven constructs)
    • If expressing a protein for the first time, good practice to do smaller-scale test expressions first (see protocol [XXX]) to determine toxicity & solubility of protein
  • 2L Baffle Flask or 4L Standard
    • Want to aim for 1/4 - 1/5 volume of the flask to get good aeration; can go up to 1/2 volume with baffle flasks
  • Shaking incubator, appropriately-sized flask clamps
  • 100mM IPTG (or other as appropriate for expression system)

DAY 1:

  1. Revive culture from frozen stock on a 2xYT plate w/ appropriate antibiotics
    • I usually add 0.2% glucose to the plates; can help prevent growth problems, esp. w/ toxic proteins
  2. Grow overnight at 37degC

DAY 2:

  1. Pick a single colony from the overnight plate, and innoculate a 60mL (1/20 vol + 10mL) culture of the expression media + antibiotics
    • I usually add 0.2% glucose to these as well
  2. Grow overnight (~16h) at 37degC *(optional) Put (sterile) growth media in 37C (non-shaking) incubator to warm overnight

DAY 3:

  1. Add antibiotic(s) to pre-warmed media, and innoculate with 50mL (1/20 vol) of the overnight starter culture
    • Save 1mL samples of pre-innoculated (blank) and 0h (just after innoculation) for OD600 measurements (should be 0.1-0.3)
  2. Put flask in 37degC incubator, shaking at 275 RPM
  3. Measure OD600 every 30-60 minutes
  4. When OD600 reaches 0.4-0.6, add 10mL (1/100 vol) IPTG to a final concentration of 1mM
    • Before adding IPTG, make sure to save 50uL of the culture for the pre-induction lane on the gel later. Add SDS-PAGE sample buffer directly to this sample (i.e. don't spin down).
  5. Continue growth at 37degC, 275RPM for 4h
  6. Remove flask, and spin down cells in 500mL centrifuge bottle
    • save 50uL of culture for the post-induction on the gel.
    • can centrifuge in two batches to get all cells in the same bottle, or resuspend in Saline / PBS and transfer to another container
  7. Freeze cell pellet:
    • For soluble proteins:
      • Freeze cell pellet in liquid nitrogen & store at -80C
    • For insoluble proteins / inclusion bodies:
      • Store bottle / pellet at -20 or -80degC
  8. Run pre- and post-induction samples on an SDS-PAGE gel (see [Protocol]); expressed protein should be visible as a heavy band of the appropriate MW present only in the post-induction sample
Edit | Attach | Watch | Print version | History: r1 | Backlinks | Raw View | More topic actions

 Barrick Lab  >  ProtocolList  >  ProtocolsLargeScaleProteinExpressionEColi

Contributors to this topic Edit topic ColinBrown
Topic revision: r1 - 2016-06-28 - 15:22:23 - Main.ColinBrown
 
This site is powered by the TWiki collaboration platform Powered by Perl This site is powered by the TWiki collaboration platformCopyright ©2024 Barrick Lab contributing authors. Ideas, requests, problems? Send feedback